Find a calculator for your next project.

Deck boards, framing lengths, footings and fixings from your chosen layout.

Plan posts, beam plies, rafters, shade slats and footing materials.

Calculate a rectangular carport frame, roof covering and foundations.

Estimate framed walls, roof, slab and hardware from a rectangular footprint.

Estimate framed walls, roof, slab and hardware from a rectangular footprint.

Estimate post-frame walls, roof, slab and hardware from a rectangular footprint.

Budget replacement door sections, track, seals and manufacturer-matched hardware.

Polygon footprint, roof surface, perimeter beams and post quantities.

Gutter stock, downspouts, hangers, outlets and end caps.

Count panels by effective cover width, with trim and fasteners.

Roof pitch, shingle bundles, underlayment and perimeter trim.

Cable allowance for an eave pattern, gutters and downspouts.

Net siding coverage, house wrap, trim and fasteners.

Soffit panels, fascia stock, edge channels and vent area.

Roof fit, nameplate DC capacity and mounting material allowances.

Calculate an equal-riser layout, tread run and stringer stock.

Gate leaves, posts, operator kits and safety accessory quantities.

Posts, bays, pickets, rails and concrete for a straight fence run.

Basket courses, stone fill and filter fabric for rectangular gabions.

Roll-width-aware turf cuts, infill, base and seam materials.

Flock-based floor and run allowances, mesh, roof and nest boxes.

Emitter demand, supply-based zones, tubing and control hardware.

Pipe sections, bedding, excavation and end protection quantities.

Trench stone less pipe displacement, drain pipe, fabric and outlets.

Seed weight and packages from your chosen label application rate.

Compare bulk mulch volume with bagged purchasing quantities.

Liner fold-down dimensions, water volume and turnover flow.

Rain-event yield, first-flush allowance and storage overflow.

Soil fill, side boards and corner supports for multiple beds.

Budget a design-approved tank and absorption field with aggregate and pipe.

Gravity route fall, excavation, pipe sections, bedding and cleanouts.

Whole pallets and individual sod pieces from measured lawn area.

Grid head layout, flow-based zoning, valves, piping and control wire.

Block courses, mortar, specified reinforcing and strip footing volume.

Brick, mortar, wall ties and flashing for a measured veneer face.

Concrete volume, delivery or bag quantities, base, forms and specified reinforcement.

Concrete volume, delivery or bag quantities, base, forms and specified reinforcement.

Concrete volume, delivery or bag quantities, base, forms and specified reinforcement.

Resurfacer yield at the selected thickness, primer and crack repair.

Solid stair pour volume, equal risers, treads and form area.

Sealer pails, coats, crack filler and primer quantities.

Clear opening checks and a budget for a basement window assembly.

Coating kits, topcoat, flakes and surface preparation allowances.

Circular wall courses, block count, base gravel and liner.

Separate compacted base and surface layers with density-based ordering.

Pavers, compacted base, bedding sand, joint sand and perimeter restraint.

Budget specified suction points, riser pipe and a selected mitigation fan.

Segmental wall courses, caps, drainage stone and base quantities.

Flat veneer, corner units, lath and mortar quantities.

Scratch, brown and finish coats using separate product coverage rates.

Required hydraulic power and the basin, discharge and valve package.

Joint volume, mortar bags and grinding consumables.

Carcass sheet allowance, shelves, doors, hinges and drawer slides.

Broadloom roll cuts, seam length, pad and tack strip.

Shelf stock, brackets, closet rods and support hardware.

Countertop mix volume, form sheets, reinforcement and sealer.

Counter area, exposed edging, backsplash and seam allowance.

Floor and wall liner, seam tape, termination bar and equipment allowance.

Stock lengths, corner allowance, fasteners and finishing materials.

Ceiling tiles, suspension grid, wall angle and hanger wire.

Room wall and optional ceiling sheets, joint compound, tape and screws.

Whole boxes, underlay, base trim and transitions for a floor.

Finish coats, sanding belts and edge discs from area and coverage.

Packages from area and product coverage at the intended R-value.

Wall paint and primer by coats, openings and label spread rate.

Horizontal board courses, stock lengths, furring and nails.

Three shower walls, floor tile, waterproofing, mortar and drain.

Window units, perimeter flashing, curbs and shaft lining.

Board layers, isolation channels, clips and acoustic sealant.

Sheet counts, joist adhesive and fastener allowances.

Tile count, adhesive, grout and optional backer board.

Equal panel openings, stiles, rails and panel sheets.

Stud layout, plates, opening framing and sheathing allowance.

Full-height strips with pattern repeat and rolls rounded per wall.

Window units, flashing tape, insulation foam and trim.

Airflow by chosen air-change rate, duct route and vent accessories.

Equivalent round duct diameter from airflow and target velocity, plus takeoff.

Fixture-unit tally and measured drain / vent material quantities.

Charging power, continuous-load allowance and conductor / conduit quantities.

Material budget from an approved head layout and pipe routes.

Element footage from room heat loss and rated output at water temperature.

Zone equipment and line-set budget using your room heat-load calculation.

Panel spaces, circuit quantities and service-material budgeting.

Home-run branches, manifold ports, tubing and fixture connections.

Tubing from spacing, loop limits, manifold ports and insulation.

Room volume, lining boards, bench material and heater planning allowance.

Running load, largest starting surge and selected equipment budget.

Tankless thermal input or storage first-hour demand, with installation materials.

Daily hardness load, regeneration-cycle capacity and plumbing supplies.

Total dynamic head and idealized shaft-power estimate with installation takeoff.

Chimney section counts and height geometry around nearby roof surfaces.

Work out cubic yards, tons and cost of gravel for a driveway, patio or garden bed.

Small smooth stones — patios, paths, play areas

Angular, locks together — driveways & bases

3/4" crushed — drainage, driveways, drains

Rounded decorative stone — beds & borders

Angular + fines — packs hard, driveways & base

Crushed + fines — packs hard under driveways

Granite fines — packs into a firm path

Paver bedding, fill

Garden beds & lawns

Subsoil — filling holes & raising grade

Rich organic matter — mix into beds & soil

Wood/bark chips — beds, around trees

Work out tons, cubic yards and cost of gravel for a driveway.

Work out how much #57 drainage gravel a French drain trench needs.

Work out the compacted gravel base a paver patio or walkway needs.

Work out gravel for a path or walkway in cubic yards, tons and cost.

Work out gravel for an RV or camper pad in tons, cubic yards and cost.

Work out gravel for a shed foundation pad in cubic yards, tons and cost.

Work out soil for a raised garden bed in cubic yards, cubic feet and bags.

Work out the sand base under an above-ground pool, by pool size.

Work out topdressing sand or soil mix to level a bumpy lawn.

Work out sand footing for a riding arena in cubic yards and tons.

Work out how many pounds of gravel or sand your fish tank needs.